Under-inflated tires waste gas for lots of folks in the Dundalk area. Think how hard it is to walk in sand – you just have to work harder because of the resistance. When your tires don’t have enough air in them, their rolling resistance is dramatically increased and it simply takes more gas to get from White Marsh to Dundalk.
Always check your tire pressure when you gas up at one of our local Dundalk service stations. If they’re low – even just a little bit – bring them up to proper pressure. There’s a sticker on the inside of your driver’s door that gives the manufacturer’s recommended tire pressure.
And don’t rely on your tire pressure monitoring system to alert you to when you need more air. The TPMS system is set to warn you when pressure drops twenty percent below recommendations. That’s severely under inflated and you needed more air a long time ago. And if you have a slow leak – get it fixed right away at Quicklane Tire & Auto Center @ Al Packer White Marsh.
All new passenger vehicles on our White Marsh MD roads now have tire pressure monitoring systems – TPMS for short. They are designed to alert you if your tires are under inflated. Since they are fairly new, a lot of people have questions about TPMS.
First off, the most important thing is that you still need to check your tire pressure every week – or at least every time you gas up. The TPMS system alert comes in when your tire is twenty percent below the factory recommendation. So if the recommended pressure is thirty five pounds per square inch, the TPMS warning won’t come on until the pressure is at twenty eight pounds. That’s significantly under-inflated. Enough to raise safety concerns.
The worst is tire failure. A severely under inflated tire can overheat and fail. Also, handling degrades to the point that you may not be able to steer out of trouble. Also under-inflated tires wear out faster and they waste fuel. So it’s costly to not stay on top of proper inflation.
What’s the practical value of the TPMS system? Well, it’s twofold. First, it can alert you when your tire is losing pressure due to a puncture or a bent rim. That’s an important warning that you might not have gotten until next time you gassed up.
The second is that we all occasionally forget to check our tire pressure. So it’s a failsafe system to let you know there’s a problem brewing.
Other things can cause your TPMS system to go off. The system also monitors itself. The sensors that are mounted in the wheels have little batteries that send a signal to the monitor. The batteries go dead over time and the TPMS system will let you know. And the sensors could break. Also road salt from our White Marsh MD roads can ruin them.
There’s also a hassle factor that your White Marsh MD tire center has to contend with. For example, when you have your tires rotated in White Marsh, the TPMS system has to be re-calibrated so that it knows which tire is on which corner of the car. Same is true for when you have new tires or winter tires installed. Flat repairs, as well.
That takes extra time. And it requires the right equipment and training. Special – and expensive – tire change machines need to be used with some sensors. It’s all complicated by the fact that there are a number of different TPMS systems in use so the tire professionals at Quicklane Tire & Auto Center @ Al Packer White Marsh need equipment and training for each kind. Tire centers have had to raise the price of some of these basic services to offset their increased costs.
Also if you add custom wheels on your Ford, you need to put in new TPMS sensors if your originals won’t work on the new rims. If you don’t your TPMS light will be on constantly and you won’t have the benefit of the warning system.
All in all, the mandated TPMS systems will save lives, so they’re worth the added hassle and expense.
Do you ever shop for shoes in one of our Baltimore area shoe stores? When buying a running shoe, is quality important? Does durability matter as long as the shoes look fabulous? Would you rather have one pair of long lasting shoes or two pair of lower quality shoes at the same price?
Is the warranty important when buying tires?
When you choose new tires in White Marsh, what’s the most important factor for you?
Give us a call at Quicklane Tire & Auto Center @ Al Packer White Marsh at (443) 777-5050 for tire recommendations.
You know, buying tires in White Marsh is a big deal. It’s a big ticket item so you know you’ll be spending a lot. You’re not only concerned about the price, but you want to know that it’ll be a long time before you need to buy new tires again.
And of course there’s the safety aspect as well. The tires do a lot of work – they carry the weight of the vehicle and you and your passengers. They need to be up to the task. You want to be sure they hold the road and provide good traction. If you carry heavy loads or tow a trailer, the tires need a high load rating to be up for the job.
As a tire professional, I think it’s important that people understand the effect of price on a tire’s performance and durability. When I was a kid, my dad had a saying. He said, “Pay twice as much and buy half as many”.
Dad applied that to a lot of things. He thought that one high quality suit would last longer and look better than two cheap suits. The saying really seems to hold true when it comes to shoes and boots, too.
I buy high-quality work shoes because I spend a lot of time on my feet. They’re more comfortable, have important safety features like steel toes and non-slip soles – and they last at least twice as long as cheap shoes. I feel I get very good value for my money.
I apply the same thinking to tires. The major tire brands that you’re familiar with are known as Tier 1 tires. These tires are well-engineered and very high quality. Comparable tires are usually in the same price range from brand to brand.
Stepping down in price you come to private label tires. Some large tire store chains carry tires with the chain’s own brand. It’s important to know that most private label tires are built by the same Tier 1 brands that you are familiar with – so they are a quality product. You can ask your tire professional who makes their private brand.
The lowest priced tires on the market are Tier 3 tires. These tend to be imported from China or South America. Since you get what you pay for, you can’t expect a Tier 3 tire to deliver the same performance and durability as the others.
So let’s say you need new tires. You’ve determined the features you need. So you have several options, including price options. Now, you’ve probably heard the term ‘it’s a 40 thousand mile tire’ or ‘it’s a 60 thousand mile tire’. Simply put, the manufacturer warrantees the tire for ‘X’ number of miles. If that’s important to you, look for the warranty.
What’s the difference in the tires with higher mileage warranties? It’s the rubber compounds and the amount of tread material. As you might expect, you’ll pay more for the longer-lasting tire.
Now the cheapest tires you can find won’t have a manufacturer’s mileage warranty or if it does, it’ll be relatively low. That brings us back to dad’s saying; if you buy the cheapest Tier 3 tire you can, you will likely go through two sets in the time it would take to wear out one set of good quality tires. And the good tires won’t cost twice as much, so you’ll end up paying more per mile driven with the cheap tires.
Hey, I realize that sometimes the budget will only allow for a Tier 3 tire. I make them available for my customers who need them because I would rather see them driving with safe, new tires than pushing their old tires beyond their safety limits. But I always counsel my customers to buy as much tire as they can afford, because it will be much less expensive in the long run.
Your tires are the only part of your vehicle that touch the road. You’re only as safe as your tires are well built.
With the recent focus in Middle River on improving fuel economy, we’ve been told how important it is to maintain our tire pressure.
Everyone in Middle River knows that tires wear out, but we all want to make them last as long as possible because they’re fairly expensive to replace. In addition to saving gas, properly inflated tires last longer. Under-inflated tires will wear out more quickly.
Some people in Middle River wonder if there is benefit to adding a few extra pounds of pressure when they fill up their tires. But actually, there isn’t. In fact, there are very good reasons not to over-inflate your tires. For one, the middle of the tread will wear unevenly because the full tread is not contacting the road properly. That also adversely affects your handling.
Every vehicle in the Middle River area has a sticker on the driver’s side door jamb that tells you the manufacturer’s recommended tire pressure. This recommendation is an integral part of the vehicle’s suspension tuning. A lot of engineering actually goes into the recommended tire pressure, so it’s important to follow it.
What else do we need to know about tire maintenance? Tire rotation and balancing are very important. Let’s start with rotation. Because the front tires handle the brunt of turning forces, the shoulders of the front tires wear more quickly than the rear tires. We rotate the tires so that they all get to do some duty on the front and they’ll all wear evenly over their life.
For most vehicles, front tires are rotated to the rear and vice versa. Others recommend a cross rotational pattern. Some vehicles use an asymmetrical tire so those tires need to stay on either the right or left side – it’ll say which on the tire. Some high performance cars have asymmetrical tires and different sizes on the front and rear. These can’t be rotated at all. Your owner’s manual will have details for your car.
How often should you rotate your tires? Your owner’s manual will have a recommendation. Your service advisor at Quicklane Tire & Auto Center @ Al Packer White Marsh can do a visual inspection to let you know if it looks like it should be done. The interval is typically around 5,000 miles.
You know, some people don’t think new tires need to be balanced. What they aren’t taking into account is the wheel. Between the wheel and the tire – even a new tire – there’s enough variation to require balancing.
When you add the valve stem and tire pressure monitoring sensors required on new cars, balancing is definitely in order. When a tire’s out of balance, it’s actually hopping down the road. You’ll feel the vibration through the steering wheel if a front tire’s out of balance and through your seat if it’s a rear tire.
Proper wheel balance promotes tire life and increases safety. Historically, lead weights have been attached to the wheel to bring it into balance. Lead gives some environmental concern, so steel weights are starting to be substituted.
Also, always use the same size tire on an axle. Different size tires on the front or on the back can lead to some real handling problems. And tire manufacturers recommend that when you get two new tires, they be installed on the rear because that’s where you need the most traction to avoid spinning-out.
Hey Baltimore, are your tires worn out? What is the standard for our MD streets? How can you tell on your Ford?
While there may be legal requirements for the Baltimore area, there are safety concerns that go beyond meeting minimum replacement mandates.
2/32 is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there’s just 2/32 of an inch – 1.6 millimeters – of tread left. It’s that level of wear that’s been called into question recently.
We’re referring to the Consumer Reports call to consider replacing tires when tread reaches 4/32 of an inch, or 3.2 millimeters. And the recommendation is backed by some very compelling studies.
The issue is braking on wet surfaces in and around Baltimore. Most of us think of our brakes doing most of the work, but if you don’t have enough tread on your tires, the brakes can’t do their job. When it’s wet or snowy, the tread of the tire is even more critical to stopping power.
Picture this: you’re driving over a water covered stretch of road near Baltimore, MD. Your tires must be in contact with the road in order to stop. That means that the tire has to move the water away from the tire so that the tire is actually contacting the road and not floating on a thin film of water.
Floating on the surface of water is called hydroplaning. So if there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.
In the study a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.
A car and a full-sized pick-up were brought up to 70 miles per hour, or 112 kilometers an hour and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:
New tire tread depth
4/32 of an inch
2/32 of an inch
So what happened with the 2/32 tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 miles an hour. Stopping distance was nearly doubled to 379 feet and it took 5.9 seconds.
Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 miles an hour with the worn tires.
Now, with the partially worn tires – at 4/32 of an inch – the car was still going at 45 miles an hour at the point where new tires brought the car to a halt. It took nearly 100 feet more room to stop and 1.2 seconds longer. That’s a big improvement. We can see why Consumer Reports and others are calling for a new standard.
Of course, stopping distances were greater for the heavier pick-up truck.
How do you know when your tires are at 4/32 of an inch? Easy; just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.
You may remember doing that with pennies. A penny gives you 2/32 to Abraham Lincoln’s head. The quarter is the new recommendation – 4/32.
How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?
For us, and we would guess for many, the answer is “no”.
At AutoNetTV we love doughnuts. So let’s pretend you have three doughnuts right in front of your for our discussion of upsizing wheels and tires. Hey, don’t eat them now – your going to need them later.
Many people want to accessorize their car – you know, make it theirs. One of the easiest ways to get a custom look is to get some new wheels. There are thousands of wheel designs out there to get you the look you want. And for many, that look includes bigger wheels. It used to be that cars came from the factory with 15 or 16 inch wheels. Now 16, 17 and even 18 inchers are standard. And the factories are offering optional wheel packages up to 20 inches or more.
Come in to Quicklane Tire & Auto Center @ Al Packer White Marsh to learn more about how you might upsize your wheels or tires. You’ll find us at 9801 Pulaski Highway in White Marsh, MD 21220.
So let’s talk about what to consider when you want to upsize your wheels. It’s not exactly a do it yourself project, so you need to know a thing or two before you get started. The most important term to know is rolling diameter. The rolling diameter is simply the overall height of your tire. Unless you want to modify your suspension, you’ll want to keep your rolling diameter the same when you upsize your wheels.
Let’s think about those three golden doughnuts in front of you. They’re all about the same size. So if we pretend they’re tires, they would have the same rolling diameter. The doughnut hole is the size of the wheel. Now pretend we’ve made the hole bigger on some. That’s like having a bigger wheel – but the rolling diameter is the same.
It’s important to keep the rolling diameter the same for several reasons. First of all, if the tire is bigger, it might not fit in the wheel well. Next the speedometer, odometer and anti-lock brake system are all calibrated for the factory rolling diameter. In order for your anti-lock brakes to work properly, the rolling diameter must stay within 3% of the factory recommendation. If you ignore that, you run the risk that your anti-lock brakes won’t work properly.
Some cars today have electronically controlled suspension that will be negatively affected by changing the rolling diameter. Let’s think about the doughnuts again. You see, as the size of the wheel gets bigger, the sidewall gets shorter. The tire holds less air, so the sidewalls are made stiffer to compensate.
Low profile tires from top manufacturers use special compounds that give the sidewall the strength it needs without compromising ride quality. As you increase your wheel size, you’ll typically get a slightly wider tire. This means that you have a larger contact patch. The contact patch is part of the tire that contacts the road. Because there’s more rubber on the road, the vehicle will handle better. And braking distances will be shorter. A lot of people with trucks or SUV’s love the extra control.
You do have to watch out that the contact patch isn’t so big that the tires rub in turns or over bumps. What we’re talking about here is fitment. Your tire professional at Quicklane Tire & Auto Center @ Al Packer White Marsh can help you get this right. He’ll install your new wheels, add spacers if needed to make sure your brakes fit inside your new wheels, and get you rolling.
Also, if you drive off-road a lot, you may need a higher profile tire to protect your new rims. And make sure your new tires have the load rating you need if you tow a trailer or haul heavy loads. Again, your tire professional at Quicklane Tire & Auto Center @ Al Packer White Marsh knows how to help.
And don’t forget about tire pressure. If you have larger rims, your new tires will hold less air and they’ll need to run a slightly higher pressure. Forget that and you’ll wear your tires out fast. Finally, get an alignment after you get your new shoes. AutoNetTV wants you to safely have the look you want.
It seems like everywhere you go in the Baltimore area you see custom wheels. Big trucks, little cars, mini-vans – it doesn’t matter, people are expressing themselves with custom wheels. Some people want smaller tires and wheels – some want larger – and some want them enormous. So where do you start if you want new wheels? We suggest you start with your budget. We know, that sounds so practical. But if the look you’re after goes beyond just new tires and wheels and enters into the world of suspension modifications, you need to be prepared for the additional cost.
Let’s start with something easy – you want to give your ride a unique look and the stock wheel size is just right for you. One of the concerns you will have is that the new wheels have the same offset as your factory wheels.
First, what is offset? The wheel bolts onto the hub on the car’s axel. The distance from the inside edge of the wheel to the point at which it bolts on, is the offset. If the new wheel has a different offset from the factory, the tires may rub on the inside or outside of the wheel well. That could lead to catastrophic tire failure.
Your tire and wheel professional at Quicklane Tire & Auto Center @ Al Packer White Marsh can help you find the right size wheel – or install adapters to make your new wheels fit. All you have to do is pick from the hundreds of styles available.
So, what if you want to upsize? Well, if it is just bigger wheels you want, but you want to keep the same overall tire diameter, that’s pretty easy. The same offset concerns apply. You need to know that the tires will likely be a little bit wider than the originals and could rub when you make sharp turns. Your tire professional at Quicklane Tire & Auto Center @ Al Packer White Marsh will help you avoid this.
It is also important to keep the same overall tire diameter because changing the rolling diameter can mess with your anti-lock brakes and stability control systems. Are you starting to see why you want to consult with a tire and wheel expert at Quicklane Tire & Auto Center @ Al Packer White Marsh? Is “super-size me” your motto? If it is, you are going to have to lift your vehicle to make room for those huge tires. A mild lift doesn’t require extensive modifications. An extreme lift means a lot of new hardware under the vehicle. It also means a lot of stock electronic systems need to be recalibrated to the new tire size. For example, your speedometer and odometer will give false readings if they aren’t recalibrated.
You should also be aware of possible performance issues. Bigger tires and wheels weigh more. Experts refer to this as unsprung weight because it isn’t held up by your suspension system. Increased unsprung weight affects performance in different ways than an equivalent amount of groceries or little soccer players in the passenger compartment. Acceleration is negatively affected. Stopping distances may also be increased – sometimes dramatically. If you want really big tires and wheels, you might need to upgrade your brakes to compensate.
Heading the other direction, some folks like to run smaller than standard wheels and lower the suspension. All of the same fitment issues still apply as well as calibration issues. Don’t think that suspension modifications are a bad thing. Many systems actually improve ride, function and performance over the stock set-up.
Regardless of your budget, you want your vehicle to continue to do all the things you need it to do. Some of those show cars and trucks you see on TV look fantastic, but have been modified in ways that may not suit your needs. For example, if you put large rims on your SUV with low profile tires, you may be in for busted rims if you go off-roading a lot. There just isn’t enough sidewall to absorb the impact of thumping over rocks.
Some people stuff the largest tires and wheels possible in their vehicles but have to severely restrict suspension travel so that the tires aren’t rubbing all day. That can lead to a very harsh ride. Again, talk with your wheel professional about all of these things: how you drive, what look you are going for, your budget and what compromises you are willing to make.
At the end of the day, you’re going to be rollin’ out of there with one sweet ride.
Always check your tire pressure when you gas up at one of our local Dundalk service stations. If they’re low – even just a little bit – bring them up to proper pressure. There’s a sticker on the inside of your driver’s door that gives the manufacturer’s recommended tire pressure.